宇航计测技术 ›› 2023, Vol. 43 ›› Issue (4): 22-30.doi: 10.12060/j.issn.1000-7202.2023.04.05

• 精密测试技术 • 上一篇    下一篇

RRT对工业摄影测量基准尺精度影响研究

王伟峰1,2，齐建伟1，黄桂平2，王新萍2，刘彦荣3   

  1. 1.黄河水利职业技术学院，开封475004；
    2.华北水利水电大学，郑州450011；
    3.航天神舟智慧系统技术有限公司，北京 100089
  • 出版日期:2023-08-15 发布日期:2023-09-19
  • 作者简介:王伟峰（1989-），男，硕士，主要研究方向：精密工程测量，数字近景工业摄影测量系统校准。
  • 基金资助:
    高分辨率对地观测系统国家科技重大专项（80-Y50G19-9001-22/23）；2022年河南省科技攻关项目（222102220031、222102210092）；2021年河南省高等学校重点科研项目（21B420002）。

Research on Effect of RRT on Industrial Photogrammetry Scale-bar Accuracy

WANG Wei-feng1,2,QI Jian-wei1,HUANG Gui-ping2,WANG Xin-ping2,LIU Yan-rong3   

  1. 1.Yellow River Conservancy Technical Institute,Kaifeng 475004,China;
    2.North China University of Water Resources and Electric Power,Zhengzhou 450011,China;
    3.Aerospace Shenzhou Intelligent System Technology Co.,Ltd，Beijing 100089，China
  • Online:2023-08-15 Published:2023-09-19

PDF (PC)

摘要： 针对工业摄影测量基准尺在实际工程中实测值与标定值互差较大、比例缩放不准确等问题，以RRT为研究对象，推导出了基准长度误差模型。从RRT圆度、中心定位稳健性、基准尺长度标定一致性以及标准长度测量等方面进行了试验研究。通过研究发现，模切覆膜型RRT圆度和中心定位稳健性远高于其它类型的RRT。模切覆膜型RRT基准尺长度标定间的重复性为1 μm，优于印刷型RRT基准尺长度标定的重复性。采用模切覆膜型RRT基准尺对标准长度的测量误差较印刷型RRT基准尺小约33%。选择模切覆膜型RRT作为基准尺的基准靶点对于提高工业摄影测量系统的测量精度具有重要参考意义。

关键词: 回光反射标志, 工业摄影测量, 基准尺, 标定

Abstract: In response to the problem of large deviation between measured values and calibrated values,as well as inaccurate proportion scaling of industrial photogrammetric scale-bar in actual engineering,a benchmark length error model was derived using retroreflective targets(RRT) as the research object.Experimental research was conducted on RRT roundness,centering robustness,consistency of scale-bar length calibration,and standard length testing.The results showed that the roundness and centering robustness of the die-cutting coated RRT were much higher than other types of RRT.The repeatability of length calibration of the die-cutting coated RRT scale-bar was 1μm,which was better than the repeatability of length calibration of the printed RRT scale-bar.The measurement error of the standard length using the die-cutting coated RRT scale-bar was about 33% smaller than that of the printed RRT scale-bar.Therefore,selecting die-cutting coated RRT as the benchmark target for the scale-bar has important reference significance for improving the measurement accuracy of industrial photogrammetric systems.

Key words: Retro-reflective target；Industrial photogrammetry, Scale-bar, Calibration

中图分类号: 

京ICP备09048426号-4　 京公网安备 11010602060144号　版权所有 © 《宇航计测技术》编辑部